MGate 5109 - 1-port Modbus-to-DNP3 gateway, 0 to 60 Degree C operating temperature
by MOXA

The MGate 5109 is an industrial Ethernet gateway for Modbus RTU/ASCII/TCP and DNP3 serial/TCP/UDP protocol conversion. All models are protected with a rugged metallic casing, are DIN-rail mountable, and offer built-in serial isolation. The MGate 5109 supports transparent mode for easily integrating Modbus TCP to Modbus RTU/ASCII networks or DNP3 TCP/UDP to DNP3 serial networks.The MGate 5109 series gateways support Modbus and DNP3 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave ID and register address, 5109 also support agent mode to exchange data between Modbus and DNP3 networks or to act as a data concentrator for multiple Modbus slaves or multiple DNP3 outstations. The rugged design is suitable for industrial applications such as power, oil & gas, and water and wastewater.

Easy Configuration via Web Console

The MGate 5109 series comes with an illustrated Quick Setup guide designed to make configuration easy. With Quick Setup, you can easily access protocol conversion modes and finish the configuration in a few steps. The MGate 5109 series also supports Auto Detection for DNP3 serial outstations, allowing the MGate 5109 to automatically acquire all outstation objects when configured as a DNP3 master.

Modbus and DNP3 Protocol Traffic Monitor

The MGate 5109 series gateways support Modbus and DNP3 Protocol Traffic Monitor for easy troubleshooting, especially during the installation stage. Communication issues could be caused by incorrect software parameters, such as slave ID and register address, or incorrect command configuration. With Modbus/DNP3 Protocol Traffic Monitor, you can check the captured data and easily identify the root cause.

Variety of Maintenance Functions

The MGate 5109 series gateway provides a web console and Telnet console for remote maintenance. Encryption communication functions, including HTTPS and SSH, are supported to provide better network security. In addition, firmware log functions are provided to record connection events and Modbus maintenance events. Users can review log data remotely through the web console.

Ethernet Interface
Protocols	Modbus TCP client/server, DNP 3.0 TCP/UDP master/outstation
Number of Ports	2 (1 IP, Ethernet cascade)
Speed	10/100 Mbps, Auto MDI/MDIX
Connector	8-pin RJ45
Magnetic Isolation Protection	1.5 kV (built-in)
• Serial Interface
Protocols	Modbus RTU/ASCII Master/Slave
Number of Ports	1
Serial Standards	RS-232/422/485, software selectable
Connectors	DB9 male
RS-485 Data Direction Control	ADDC® (automatic data direction control)
Pull High/Low Resistor for RS-485	1 kΩ, 150 kΩ
Terminator for RS-485	120 Ω
Isolation	2 kV (built-in)
• Serial Communication Parameters
Data Bits	7, 8
Stop Bits	1, 2
Parity	None, Even, Odd, Space, Mark
Flow Control	RTS/CTS, RTS Toggle (RS-232 only)
Baudrate	50 bps to 921.6 kbps
• Serial Signals
RS-232	TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422	Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w	Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w	Data+, Data-, GND
• Modbus
Functions Supported	1, 2, 3, 4, 5, 6, 15, 16, 23
Max. No. of Commands	100
Max. No. of Connections	MGate as Modbus TCP Master: 32 slave connections MGate as Modbus TCP slave: 16 master connections
• DNP3
Max. No. of Connections	• Transparent mode: 16 master connections or 32 outstation connections • Agent mode: MGate as DNP3 TCP/UDP master: 32 outstation connections MGate as DNP3 TCP/UDP outstation: 1 master connection
DNP3 Internal Database	• For each outstation: Binary Inputs: 256 points Analog Inputs: 64 points Counters: 64 points Binary Outputs: 256 points Analog Outputs: 64 points • When the MGate 5109 is configured as a DNP3 outstation Bina
• Software
Configuration Options	Web Console, Serial Console Utility
Configuration	MXview, SNMP (v1, v2, v3), Private MIB
• Physical Characteristics
Housing	Metal, IP30
Weight	507 g (1.12 lb)
Dimensions	36 x 105 x 140 mm (1.42 x 4.14 x 5.51 in)
Storage Card Slot	1 microSD (SDHC) card slot supports up to 32 GB
Relay Alarm Circuit	3-pin circuit with current carrying capacity of 2 A @ 30 VDC
• Environmental Limits
Operating Temperature	Standard Models: 0 to 60°C (32 to 140°F)  Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature	-40 to 85°C (-40 to 185°F)
Ambient Relative Humidity	5 to 95% (non-condensing)
Vibration	IEC 60068-2-6, IEC 60068-2-64
Shock	IEC 60068-2-27
Drop	IEC 60068-2-32
• Power Requirements
Input Voltage	12 to 48 VDC
Input Current	455 mA @ 12 VDC; 125 mA @ 48 VDC
Power Connector	Terminal block
• Standards and Certifications
Safety	UL 508, EN 60950-1
Hazardous Location	Class 1 Division 2, ATEX, IECEx
EMC	EN 55022/24
EMI	CISPR 22, FCC Part 15B Class B
EMS	IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m IEC 61000-4-4 EFT: Power: 4 kV; Signal: 2 kV IEC 61000-4-5 Surge: Power: 2 kV; Signal: 2 kV IEC 61000-4-6 CS: 150 kHz to 80 MHz: 10 V/m IEC 61000-4-8 PFMF
• MTBF (mean time between failures)
Time	859,422 hrs
Standard	Telcordia SR332

MGate_5109.pdf

689 K