07013670 IDS-409F3-C2SD20-SD40 - Industrial Managed Ethernet Switch - 9 ports: 6 x 10/100/1000Base-T RJ-45 ports and 2 x 100Ba
by PERLE

Simple deployment

Zero-touch discovery using Dynamic Host Control Protocol (DHCP), Perle’s “Fast Setup”  for first time installation, provides simple deployment  in Ethernet environments

Resiliency

• STP and RSTP protocols for fast recovery.
• Perle’sP-Ring protocol for fast convergence in ring topologies
• Link Standby is a link recovery feature for two links that provides a simple alternative to spanning tree protocols for link redundancy

Manageability

• Web Device Manager, Telnet, SNMP and Perle’s PerleView NMS for centralized management
• In-band management via RJ45 or USB serial ports
• Use an IPv4 or IPv6 address
• Removable MicroSD flash for configuration files and firmware backup and restoration

Rugged design for harsh environments

• Corrosion resistant case
• Programmable Controller Safety certified
• Certified for hazardous locations
• Extended industrial temperature models

Reliable operation

• Fan-less, no moving parts
• Dual power input. Connect to separate power sources for redundancy.
  • Reverse polarity protection
  • Overload current protection
• Handles vibration and shock conditions found in industrial environments

Real-time Ethernet performance

• Fast wire-speed , store and forward switching
• Auto-sensing for speed and duplex
• Auto-mdi/mdix-crossover works with straight and crossover cables

Auto-sensing of port speed and auto-negotiation of duplex on all switch ports for optimizing bandwidth

Medium-dependent interface crossover ( Auto-MDIX ) capability on 10/100 and 10/100/1000 mbps  interfaces that enables the interface to automatically detect the required cable type ( straight thru or crossover ) and to configure the connection appropriately

IEEE 802.3x flow control on all ports. ( The switch does not initiate pause frames )

Storm control prevents traffic on a LAN from being disrupted by a broadcast, multicast, or unicast storm on one of the physical interfaces. A LAN storm occurs when packets flood the LAN, creating excessive traffic and degrading network performance. Storm Control enables limits to be placed on broadcast, multicast and unicast traffic

This feature enables the manual configuration of the MAC addresses on a per port basis. Flooding is prevented by retaining MAC entries across a reboot of the switch.

Port Blocking provides the ability to block the flooding of unknown layer 2 unicast and multicast traffic on an Interface

Internet Group Management Protocol ( IGMP ) constrains the flooding of multicast traffic by dynamically configuring Layer 2 interfaces so that multicast traffic is forwarded to only those interfaces associated with IP multicast devices.

IGMPv1, v2, v3, IGMP snooping querier mode, IGMP report suppression, topology change notification and robustness variable features are supported

In some network environments, it is desirable to move an Ethernet from one switch port to another and have the device come on-line quickly. The Port Quick Disconnect feature if enabled, provides an immediate age-out of the MAC addresses learned on the port when the port status changes from a link-up to a link-down state

The Perle Web Device Manager is an embedded Web based application that provides an easy to use browser interface for managing the switch. Unlike competitive products, Java applet technology is not required or used

A familiar text-based Command Line Interface that is based on accepted industry standard syntax and structure. Ideal for CCNA and CCNP trained engineers, this interface is available via in-band Telnet or the out-band serial console port

Manage the switch with an snmp compatible management station that is running platforms such as HP Openview or Perle’s PerleVIEW NMS. SNMP V1 and V2C

PerleVIEW

PerleVIEW is Perle’s SNMP-based network management system that provides a view of the network with a large scale of Perle networking devices.

Manage with an IPv4 or IPV6 address

Automates configuration of switch information such as IP address, default gateway, hostname and Domain Name System ( DNS ) as well as TFTP server names. Firmware and configuration file locations are provided through options 54, 66, 67, 125 and 150

DHCP Relay is used for forwarding requests from DHCP clients when they are not on the same physical subnet. As a DHCP relay agent the switch operates as a Layer 3 device that forwards DHCP packets between clients and servers.

Normally used in metro or large enterprise deployments DHCP Option 82 insertion is used to provide additional information on “physical attachment” of the client.  As per RFC 3046, option 82 enables additional pre-defined information to be inserted into the DHCP request packet  ( for DHCP Servers that support this option )

LLDP-Link Layer Discovery Protocol as per IEEE 802.1AB is a neighbor discovery protocol that is used for network devices to advertise information about themselves to other devices on the network. This protocol runs over the data-link layer, which allows two systems running different network layer protocols to learn about each other ( via TLVs – Type-Length-Value )

Firmware can be transferred via TFTP, HTTP or via insertion of a microSD card. Text-based files that can be created or edited by common text editors.

IEEE 802.1D now incorporated in IEEE 802.1Q-2014, STP prevents bridge loops and the broadcast radiation that results from them.

Other Spanning Tree features include BPDU guard, Root guard, loop guard, root guard and TCN Guard

Interoperable with STP, RSTP ( IEEE 802.1w ) takes advantage of point-to-point wiring and provides rapid convergence of the spanning tree. Reconfiguration of the spanning tree can occur in less than 1 second

P-Ring

Perle’s Ring Protocol provides resilient operation of a network made up of managed switches in a ring topology. The implementation prevents a switch loop scenario and also enables communication within the ring if a failure occurs somewhere in the ring.

P-Ring also has an auto-configuration feature that automatically determines the master control switch in the ring reducing installation time.

Recovery time of 10 ms or better in rings composed of up to 14 switches

Up to 255 VLANS across a VLAN ID range of 1 to 4094

Perle switches provide the ability to configure management VLAN interfaces. This enables network administrators to access the switch’s management interface from separate VLAN networks

IP ToS/DSCP and IEEE 802.1p CoS

Weighted Fair Queuing or Strict Queuing

• 4 traffic class queues per port
• output queue mapping
• DSCP to output queue mapping

N:1 Port Mirroring is a method of monitoring network traffic. With port mirroring enabled, the switch sends a copy of one or more ports to a predefined destination port. Selection of Transmit, Receive frames or both can be made

RMON statistics provided for statistics, history, alarms and events for network monitoring and traffic analysis

Facility for logging systems messages to an external SYSLOG server

Facility for logging systems messages locally

Layer 2 traceroute to identify the path that a frame takes from source to destination

A test that enables the detection of potential copper cabling issues such as pair polarity pair swaps and excessive pair skew as well as any opens, shorts or any impedance mismatch. Will report the distance in the cable to the open or short.

Provides the status of power supplies of the switch

The switch can monitor global switch conditions as well as individual ports. These alarms can be configured to send messages to ;

• an internal log file
• external Syslog server
• SNMP trap server
• An external alarm device such as a bell, light or other signaling device via the switch’s built-in dry contact alarm relay

Global Status Monitoring Alarms

• Dual power supply alarm

Port Status Monitoring Alarms

• Link Fault Alarm ( IE loss of signal )
• Port not forwarding alarm
• Port not operating alarm ( failure upon start up tests )
• FCS Bit error rate alarm

When enabled, energizes the built-alarm relay triggering an external alarm circuit such as a bell, light or other signaling device according to alarm conditions set

IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-T(X) and 100Base-X
IEEE 802.3ab for 1000Base-T
EEE 802.3z for 1000BaseX 
IEEE 802.3x for Flow Control
IEEE 802.1D-2004 for Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.3ad for Port Trunk with LACP
IEEE 802.1AB LLDP

RFC 1213-MIB II
RFC 1493-BRIDGE-MIB
RFC 1907-SNMPv2-MIB
RFC 2012-TCP-MIB
RFC 2013-UDP-MIB
RFC 2578-SNMPv2-SMI
RFC 2579-SNMPv2-TC
RFC 2819-RMON-MIB
RFC 4502-RMON2-MIB
RFC 2613-SMON-MIB
RFC 2863-IF-MIB
RFC 4363-Q-Bridge-MIB and P-Bridge MIB 
RFC 4318-RSTP-MIB
IP-MIB
LLDP-MIB