FP101E/SFP/DC – Industrial Gigabit SFP Media Converter; 10/100/1000BaseTX (RJ45); 100/1000 (SFP); -40 to 75°C; 12-56V DC
by PATTON

Patton™'s FP101E-SFP-DC - converts singlemode or multimode fiber to a copper Ethernet signal. The combination of high bandwidth and noise immunity of fiber makes these ideally suited for many applications including IP security cameras, IP speakers, VoIP phones, Wireless Access Points, POS kiosks, BACs, PLCs and more.

Because Ethernet over Cat 5e/6 cables is limited to only 100 meters (328 feet), using fiber as a backhaul allows for a massive increase in distances. SFP options for multimode can reach up to 2 km (1.24 miles) and singlemode options can range as far as 120 km (74 miles). In addition to the reach, you get Fiber's™ superior immunity to noise and, harmful transients (surges).

The FP101E is housed in an IP30 rated DIN rail, wall-mount enabled enclosure and has a wide operating temperature of -40 to 75C (-40 to 167F). Its rugged design and wide temperature range makes it an ideal media converter for industrial or harsh environments.

The Fiberplex 101E is very simple to use, completely plug and play. LEDs will make it clear when power is detected and when data is passing both on the copper and fiber lines

Ethernet Interfaces	1x100/1000 Mbps SFP Port 1xRJ-45 10/1000/1000BaseT(x) Auto MDI-x / MDI crossover Auto-Negotiation, 10/100/1000 Mbps, Full or Half Duplex
Networking	IEE 802.3x Flow Control and Back Pressure Back-plane (switching fabric): 4 Gbps Converter Mode: Port speeds are the same Switch Mode/Store and Forward: Port speeds are not the same Jumbo Frame: 16Kb MAC Address Table Size: 1K Packet Buffer Size: 512Kb
IEEE Standards	IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-Tx Fast Ethernet IEEE 802.3ab 1000Base-T Gigabit Ethernet IEEE 802.3z 1000Base-x Gigabit Ethernet
Management	Plug and Play operation LEDs (Power, Copper Tx Link & Activity, Fiber (SFP) Link & Activity DIP Switch Functions (Link Fault Pass Through On or Off, SFP Speed 100 or 1 Gigabit)
Alarm Relay Contact	Relay output w/ current carrying capacity of 1A@24VDC Short Circuit Mode: Power fails Open Circuit Mode: Power is connected
Power Input Connector	Removable 4-pin terminal block Wire range: 0.34 to 2.5 mm^2 Solid wire (AWG): 12-24/14-22 Stranded wire (AWG): 12-24/14-22 Torque: 5lb-In/0.5Nm/0.56Nm Wire Strip length: 7-8 mm
Power Input	4-pin terminal block 12-56 VDC input Relay switch for alarm 100-240 VAC via optional power adapter
Power Consumption	3 watts at 48 VDC full load
Physical	4.07L x 1.26W x 3.21D inches (103.5L x 32W x 81.5D mm) Unit Weight: 2.5 lb (1.13 kg) Shipping Weight: 3.0 lb (1.36 kg)
Regulatory Approvals	Safety: LVD (EN62368-1) EMC: CE, FCC, EN55032/24 EMI: CISPR 32, FCC Part 15B Class A EMS IEC 61000-4-2 ESD: Contact: 6KV; Air: 8KV IEC 61000-4-4 EFT: Power: 2KV; Signal: 2KV IEC 61000-4-5 Surge: Power: 2KV; Signal: 2KV Free Fall: EN60068-2-32 Shock: EN60068-2-27 Vibration : EN60068-2-6
Environmental	Ambient Temperature Operating: -40 to 75°C (-40 to -167°F) Storage: -40 to 85°C (-40 to -185°F) Relative Humidity 5 to 95% non-condensing Protection Class IP30

FP101E_SFP_DC.pdf

3,340 K