|
|
ioLogik E1262 - Remote Ethernet I/O with 8TC, and 2-port Switch by MOXA
|
|
|
- Support Modbus/TCP Protocols
- Active communication with patented Active OPC Server
- 2-port Ethernet switch for daisy-chain topologies
- Easy mass deployment and configuration with ioSearch utility
- Save time and wiring cost with peer-to-peer communication
- User-defined Modbus/TCP addressing
- Simplify I/O managment with MXIO library on either Windows or Linux platform
- Supports SNMPv1/v2c
UL/cUL Class I Division 2, ATEX Zone 2 certification
Wide operating temperature: -40 to 75°C ( -40 to 167°F )
|
|
|
Introduction
Daisy-chained Ethernet I/O ConnectionA new daisy-chained Ethernet I/O concept is now available. The ioLogik E1262 industrial Ethernet remote I/O has two embedded Ethernet switch ports that allow information to flow to another local Ethernet device or connect to the next ioLogik in the daisy-chain.
Applications such as factory automation, security and surveillance systems, and tunnel monitoring, can make use of daisy-chained Ethernet for building multi-drop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with the multi-drop configuration typically used in fieldbus applications. The daisy-chain function on the Ethernet remote I/O ioLogik E1262 not only increases the connection between machines and panels, but also lowers the cost of buying separate Ethernet switches, and at the same time reduces labor fees and cabling by a large percentage. For example, if a production facility contains 700 stations (20 points per station), the wiring cost reduction can reach 15% of the total implementation cost.
Saving Time and Wiring Costs with Peer-to-Peer Communications
In remote automation applications, the control room and sensors are often far removed, making wiring over long distances a constant challenge. With peer-to-peer networking, users may now map a pair of ioLogik E1200 series modules so that input values will be directly transferred to output channels, greatly simplifying the wiring process and reducing wiring costs.
User-definable Modbus/TCP Addressing for Painless Upgrading of Existing Systems
For Modbus devices that are controlled and detected by fixed addresses, users need to spend a vast amount of time researching and verifying the configurations. Users need to locate each device’s networking details like I/O channels, or vendor-defined addresses to enable the initial or start address of a SCADA system or PLC. The ioLogik E1200, with user-definable Modbus/TCP addressing, offers greater flexibility, and setup is easy. Instead of worrying about individual devices, users simply configure the function and address map to fit their needs.
ioLogik E1262 Specifications |
• Inputs and Outputs |
Thermocouple Inputs |
8 channels |
Isolation |
3k VDC or 2k Vrms |
• Thermocouple Input |
Sensor Type |
J (0 to 750°C), K (-200 to 1250°C), T (-200 to 350°C), E (-200 to 900°C), R (-50 to 1600°C), S (-50 to 1760°C), B (600 to 1700°C), N (-200 to 1300°C) |
Millivolt Type |
• Mode: ±78.126 mV, ±39.062 mV, ±19.532 mV
• Fault and over-voltage protection: -35 to +35 VDC (power off);
-25 to +30 VDC (power on) |
Sampling Rate |
• All channels: 12 samples/sec
• Per channel: 1.5 samples/sec
• Only one channel enabled: 12 samples/sec |
Resolution |
16 bits |
Accuracy |
±0.1% FSR @ 25°C
±0.3% FSR @ -40 and 75°C |
Input Impedance |
10M ohms |
• Power Requirements |
Power Consumption |
118 mA @ 24 VDC |
• MTBF (mean time between failures) |
Time |
631,418 hrs |
Database |
Telcordia (Bellcore) |
Common Specifications |
• LAN |
Ethernet |
2 switched 10/100 Mbps RJ45 ports |
Protection |
1.5 kV magnetic isolation |
Protocols |
Modbus/TCP, TCP/IP, UDP, DHCP, BOOTP, HTTP |
• Power Requirements |
Power Input |
24 VDC nominal, 12 to 36 VDC |
• Physical Characteristics |
Wiring |
I/O cable max. 14 AWG |
Dimensions |
27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in) |
Weight |
Under 200 g |
Mounting |
DIN rail or wall |
• Environmental Limits |
Operating Temperature |
Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
Storage Temperature |
-40 to 85°C (-40 to 185°F) |
Ambient Relative Humidity |
5 to 95% (non-condensing) |
Altitude |
Up to 2000 m |
Note |
Please contact Moxa if you require products guaranteed to function properly at higher altitudes. |
• Standards and Certifications |
Safety |
UL 508 |
EMI |
EN 55022; EN 61000-3-2; EN 61000-3-3;
FCC Part 15, Subpart B, Class A |
EMS |
EN 55024, EN 61000-4-2, EN 61000-4-3,
EN 61000-4-4, EN 61000-4-5, EN 61000-4-6,
EN 61000-4-8, EN 61000-4-11 |
Shock |
IEC 60068-2-27 |
Freefall |
IEC 60068-2-32 |
Vibration |
IEC 60068-2-6 |
Green Product |
RoHS, CRoHS, WEEE |
Hazardous Location |
UL/cUL Class I Diision 2, ATEX Zone 2 |
|
|