Need assistance or guidance?

Contact us @: 1-800-301-9097
Login / Register Contact Us
 
IMC-P111FX-SS-SC-LV - Industrial IEC 61850-3 Ethernet to fiber media converter with 1x10/100Base-T(X) to 1x100Base-FX Single Mod by ORing Industrial Networking

IMC-P111FX-SS-SC-LV - Industrial IEC 61850-3 Ethernet to fiber media converter with 1x10/100Base-T(X) to 1x100Base-FX Single Mod
by ORing Industrial Networking

Write a review Write a review
  • Designed for Railway application and fully compliant with the requirement of IEC 61850-3 and IEEE 1613
  • Leading EN50155-compliant Ethernet switch for rolling stock application
  • Supports 1 port 10/100Base-T(X) auto-negotiation and auto-MDI/MDI-X
  • Support Ethernet to fiber or Ethernet to SFP port
  • Support LFP (Link Fault Pass-through) function
  • Supports full/half duplex operationDIN-Rail and wall mounting enabled
  • Supports store and forward transmission
  • Supports relay output for power failed alarm
  • Provided DIP-Switch to setting function
  • High reliability and rigid IP-30 housing
  • DIN-Rail and panel mounting enabled

IMC-P111 series is a cost-effective solution for the conversion between 10/100Base-T(X) and 100Base-FX interface, it allows you to extend communication distance by optical fiber. IMC-P111 series are designed for power substation application and rolling stock application, fully compliant with the requirement of IEC 61850-3 and IEEE 1613. IMC-P111 series supports MDI/MDIX auto detection, so you don’t need to use crossover wires. IMC-P111 series with wide operating temperature range from -40 ~ 85oC and accepts a wide voltage range power inputs, so it is suitable for harsh operating environments. IMC-P111 series also support the LFP (Link Fault Pass-through) feature. When one side of the link fails, the other side continues transmitting packets, and waiting for a response that never arrives from the disconnected side. Use the DIP-Switch to enable the LFP function, then IMC-P111 series will force the link to shutdown as soon as noticed that the other link has failed, giving the application software a chance to react to the situation. Therefore, the IMC-P111 series is reliable media converter and can satisfy most demand of power substation and rolling stock application.

IMC-111 series also support the LFP (Link Fault Pass-through) feature. When one side of the link fails, the other side continues transmitting packets, and waiting for a response that never arrives from the disconnected side. Use the DIP-Switch to enable the LFP function, then IMC-111 series will force the link to shutdown as soon as noticed that the other link has failed, giving the application software a chance to react to the situation. Therefore, the IMC-111 series is reliable media converter and can satisfy most demand of operating environment.

 

Physical Ports    
Port type 100Based-FX Single-mode Port  
Fiber Ports Number 1  
Fiber Diameter (µm) 9/125 µm  
Fiber Optical Connector SC  
Typical Distance (Km) 30 Km  
Wavelength (nm) 1310 nm  
Max. Output Optical Power (dbm) -8 dbm  
Min. Output Optical Power (dbm) -15 dbm  
Max. Input Optical Power (Saturation) 0 dbm  
Min. Input Optical Power (Sensitivity) -34 dbm  
Link Budget (db) 19 db  
Ethernet Standards IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-T(X) and 100Base-FX
IEEE 802.3x for Flow control
Processing Store-and-Forward
DIP-Switch setting DIP-Switch 1 for LFP mode selection : (ON) enable / (OFF) disable
DIP-Switch 2 for Ethernet speed selection : (ON)10Mbps / (OFF) 10/100Mbps Auto-negotiate
DIP-Switch 3 for Ethernet full/half duplex selection : (ON) Half-duplex / (OFF) Full/Half-Duplex Auto-negotiate
DIP-Switch 4 for fiber full/half duplex selection : (ON) Half-Duplex / (OFF) Full-Duplex
LED Indicators    
Power indicator Green : Power LED x 3 (ON : power input on-line / (OFF) power input off-line
10/100Base-T(X) RJ45 port indicator Green for port Link/Act – (ON) Link up / (Blinking) Acting / (OFF) Link down
Amber for 100Mbps/10Mbps indicator – (ON) Working at 100Mbps / (OFF) Working at 10Mbps
Green for port duplex indicator – (ON) Full-Duplex / (OFF) Half-Duplex
100Base-FX fiber port indicator Green for fiber port Link/Act - (ON) Link up / (Flash) Acting / (OFF) Link down
Green for fiber port duplex indicator – (ON) Full-Duplex / (OFF) Half-Duplex
LFP statue indicator Amber LED – (ON) LFP function fail / (OFF) LFP function disablem
Fault Indicator Amber : Indicate unexpected event occurred  
Power    
Input power Triple DC inputs. 12~48VDC on 7-pin terminal block. 12~45VDC on power jack
Power consumption (Typ.) 12 Watts
Overload current protection Present
Reverse polarity protection Present on terminal block
Physical Characteristics    
Enclosure IP-30
Dimension (W x D x H) 52 (W) x 106.1 (D) x 144.3 (H)mm (2.05 x 4.18 x 5.68 inch)
Weight (g) 660 g
Environmental    
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -40 to 85°C (-40 to 185°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory Approvals    
Power Automation IEC 61850-3, IEEE 1613
EMI FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN50121-4
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS), EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Warranty 5 years

Copyright © 2024 iComTech. All rights reserved. Shopping Cart Software powered by ecMidas.