CL-SFP/XC – CopperLink SFP Long Range, High-Speed Single-Pair GigE Ethernet Extender; 1.5-18 Mbps Line Rate
by PATTON

The Patton CopperLink CL-SFP-xC - is a single pair, low power SFP (Small Form-factor Pluggable) Ethernet-over-Copper Extender. The module can be plugged into any Router, Ethernet Switch or Media Converter that has SFPs slots that support 100BASE-Fx and/or 1000BASE-x.

The Patton CopperLink SFP is a single pair, low power SFP (Small Form-factor Pluggable) Ethernet-over-Copper Extender. The module can be plugged into any Router, Ethernet Switch or Media Converter that has SFPs slots that support 100BASE-Fx and/or 1000BASE-x

The CopperLink SFP supports distances of up to 3.5 miles (18,000 feet, 6.2 Km) over 1 pair of wires. The embedded firmware is optimized for full duplex rates between 1.5 and 18Mbps.

The CopperLink SFP supports distances of up to 3.5 miles (18,000 feet, 6.2 Km) over 1 pair of wires. The embedded firmware is optimized for full duplex rates between 1.5 and 18Mbps.

The device uses a proprietary implementation of Pulse Amplitude Modulation (PAM) technology with lower frequency bandwidths compared to VDSL/ADSL technology. As a result, the transmission presents less interference with other signals in wire bundles making the transmission safer and more reliable.

The device uses a proprietary implementation of Pulse Amplitude Modulation (PAM) technology with lower frequency bandwidths compared to VDSL/ADSL technology. As a result, the transmission presents less interference with other signals in wire bundles making the transmission safer and more reliable

Configuration is done with a user-friendly Web GUI, or with an intuitive CLI accessed via Telnet. The units can set to fixed transmission rates or automatically adapt the transmission rate.

Configuration is done with a user-friendly Web GUI, or with an intuitive CLI accessed via Telnet. The units can set to fixed transmission rates or automatically adapt the transmission rate

The link synchronization in Fixed Rate Mode is very fast at between 2 and 10 seconds. In Auto Rate Mode, SFP modems automatically adjust the transmission rate to the optimum performance that line conditions can support. The copper line interface has 1500V RMS isolation and meets the ITU-T K.20/K.21 protection standard.

The link synchronization in Fixed Rate Mode is very fast at between 2 and 10 seconds. In Auto Rate Mode, SFP modems automatically adjust the transmission rate to the optimum performance that line conditions can support. The copper line interface has 1500V RMS isolation and meets the ITU-T K.20/K.21 protection standard

Link Quality Monitoring provides users with link performance information useful during installation and maintenance. Fast Link Recovery Automatic Active Device Detection allows the CL-SFP to detect an active device on the remote side of the line and recognize a line failure.

Link Quality Monitoring provides users with link performance information useful during installation and maintenance. Fast Link Recovery Automatic Active Device Detection allows the CL-SFP to detect an active device on the remote side of the line and recognize a line failure

The units come with two different options for terminating wires including a Single Pair Ethernet compliant (IEC 63171-6) metal latching connectors and Combicon xC with Snap-in Locking connector.The units come with two different options for terminating wires including a Single Pair Ethernet compliant (IEC 63171-6) metal latching connectors and Combicon xC with Snap-in Locking connector

Line Interface	Output Voltage: 2.0 to 2.6 V Peak-to-Peak Line Impedance: Typical 114 Ohms Transmit Bandwidth: 50kHz…36MHz Number of Pairs: One (1) Bit Rate: 1.1536 to 18048 Kbps Connector Types: Phoenix Contact, 2-pin, 1815264 or AMPHENOL 2-pin, MSPE-J2L0-E00 Overvoltage Protection: ITU-T K.20 and K.21
SFP Host Interface	Standard: IEEE-802.3 Data Rate: 100Base-Fx / 1000Base-x Connector Type: SFP Host Connector Data (MSA Compliant)
Power Supply (MSA Compliant SFP Host Power)	Input Voltage: 3.135 to 3.465 VDC Input Current: Maximum 255 mA Power Consumption: Typically, 0.73 Watts (Link up @18 Mbps, 1000Base-x host)
Maximum Latency (In Milliseconds per leg)	64-byte packets: 0.788 @ 1536 kbps, 0.137 @ 10000 kbps and, 0.085 @18048 kbps 128-byte packets: 1.144 @ 1536 kbps, 0.283 @ 10000 kbps and, 0.136 @18048 kbps 256-byte packets: 1.670 @ 1536 kbps, 0.390 @ 10000 kbps and, 0.239 @18048 kbps 512-byte packets: 2.980 @ 1536 kbps, 0.658 @ 10000 kbps and, 0.444 @18048 kbps 1024-byte packets: 6.131 @ 1536 kbps, 1.250 @ 10000 kbps and, 0.856 @18048 kbps 1280-byte packets: 7.557 @ 1536 kbps, 1.614 @ 10000 kbps and, 1.061 @18048 kbps 1518-byte packets: 8.641 @ 1536 kbps, 1.852 @ 10000 kbps, and 1.252 @18048 kbps 2048-byte packets: 11.530 @ 1536 kbps, 2.439 @ 10000 kbps and, 1.678 @18048 kbps
Jitter (In Microseconds)	1536 kbps: 3.2 μs 10000 kbps: 1.0 μs 18048 kbps: 1.2 μs
Environmental	Storage: ETS 300 019-1-1 Class 1.2 (-40C … +85C) Transportation: ETS 300 019-1-2 Class 2.3 (-40C … +70C) Operation: ETS 300 019-1-3 Class 3.2 (-40C … +85C)
Dimensions CL-SFP/xC	w/o connector: 13.7(W) x 68.6(D) x 13.8(H) mm with connector: 13.7(W) x 74.9(D) x 13.8(H) mm with snap-in installed: 14.5(W) x 76.1(D) x 13.8(H) mm
Dimensions CL-SFP/SPE	w/o connector: 13.7(W) x 71.2(D) x 13.8(H) mm with SPE connector: 13.7(W) x 98.4(D) x 13.8(H) mm
EMC and Safety Standards	Safety: EN 62368-1:2020/A11:2020, IEC 62368-1:2020/A11: 2020 EMC: EN 300 386 V2.1.1:2016, EN 55032:2015/A11:2020 class B, EN 55035:2017/A11:2020 criterion A, EN 61000-4-2:2009 ± 8 kV contact discharge; ± 15 kV air discharge, EN 61000-4-3:2020 10 V/m (80-1000 MHz), EN 61000-4-4:2012 ± 4 kV data line, EN 61000-4-5:2014 + A1:2017 ± 2 kV data line and, EN 61000-4-6:2014 10 V (150 kHz-80 MHz)