|
|
|
Moxa AWK-3131A-EU-T - Industrial IEEE 802.11a/b/g/n wireless AP/bridge/client
by MOXA
|
|
|
|
- IEEE 802.11a/b/g/n AP/bridge/client support
- Seamless roaming with Turbo Roaming
- Complete redundancy with AeroLink Protection
- Integrated antenna and power isolation
- -40 to 75°C operating temperature range (-T models)
- 5 GHz DFS channel support
|
|
|
Advanced 802.11n Industrial Wireless Solution
• 802.11a/b/g/n compliant AP/bridge/client for flexible deployment
• Software optimized for long distance (LoS, 1 km) wireless communication with external high-gain antenna (available on 5 GHz)
• Supports 60 clients connected concurrently
• DFS channel support allows a wider range of 5 GHz channel selection to avoid existing wireless infrastructure and interference
Advanced Wireless Technology
• Seamless roaming with Client-based Turbo Roaming for < 150 ms roaming recovery time between APs (Client mode)
• Supports AeroLink Protection for creating a redundant wireless link (< 300 ms recovery time) between AP and clients (Client mode)
Industrial Ruggedness
• Integrated antenna and power isolation designed to provide 500 V insulation protection against external electrical interference
• Hazardous location wireless communication with Class I Div II and ATEX Zone 2 certifications
• -40 to 75°C wide operating temperature models (-T) provided for smooth wireless communication in harsh environments
| • WLAN Interface |
| Standards |
IEEE 802.11a/b/g/n for Wireless LAN
IEEE 802.11i for Wireless Security
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X)
IEEE 802.3ab for 1000BaseT
IEEE 802.3af for Power-over-Ethernet
IEEE 802.1D for Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1Q for VLAN |
| Spread Spectrum and Modulation (typical) |
• DSSS with DBPSK, DQPSK, CCK
• OFDM with BPSK, QPSK, 16QAM, 64QAM
• 802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBPSK @ 1 Mbps
• 802.11a/g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps
• 802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported) |
| Operating Channels (central frequency) |
US:
2.412 to 2.462 GHz (11 channels)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (8 channels, excluding 5.600 to 5.640 GHz)*
5.745 to 5.825 GHz (5 channels)
EU:
2.412 to 2.472 GHz (13 channels)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (11 channels)*
JP:
2.412 to 2.484 GHz (14 channels)
5.180 to 5.240 GHz (4 channels)
5.260 to 5.320 GHz (4 channels)*
5.500 to 5.700 GHz (11 channels)* |
| *DFS (Dynamic Frequency Selection) channel support |
In AP mode, when a radar signal is detected, the device will automatically switch to another channel. However according to regulations, after switching channels, a 60-second availability check period is required before starting the service. |
| Security |
• SSID broadcast enable/disable
• Firewall for MAC/IP/Protocol/Port-based filtering
• 64-bit and 128-bit WEP encryption, WPA/WPA2-Personal and Enterprise (IEEE 802.1X/RADIUS, TKIP, and AES) |
| Transmission Rates |
802.11b: 1, 2, 5.5, 11 Mbps
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n: 6.5 to 300 Mbps (multiple rates supported) |
| Transmitter Power |
802.11b:
Typ. 26±1.5 dBm @ 1 Mbps, Typ. 26±1.5 dBm @ 2 Mbps
Typ. 26±1.5 dBm @ 5.5 Mbps, Typ. 25±1.5 dBm @ 11 Mbps
802.11g:
Typ. 23±1.5 dBm @ 6 to 24 Mbps, Typ. 22±1.5 dBm @ 36 Mbps
Typ. 20±1.5 dBm @ 48 Mbps, Typ. 19±1.5 dBm @ 54 Mbps
802.11n (2.4 GHz):
Typ. 23±1.5 dBm @ MCS0/8 20 MHz,
Typ. 18±1.5 dBm @ MCS7/15 20 MHz
Typ. 23±1.5 dBm @ MCS0/8 40 MHz,
Typ. 17±1.5 dBm @ MCS7/15 40 MHz
802.11a:
Typ. 23±1.5 dBm @ 6 to 24 Mbps, Typ. 21±1.5 dBm @ 36 Mbps
Typ. 20±1.5 dBm @ 48 Mbps,Typ. 18±1.5 dBm @ 54 Mbps
802.11n (5 GHz):
Typ. 23±1.5 dBm @ MCS0/8 20 MHz,
Typ. 18±1.5 dBm @ MCS7/15 20 MHz
Typ. 23±1.5 dBm @ MCS0/8 40 MHz,
Typ. 18±1.5 dBm @ MCS7/15 40 MHz |
| Note |
Based on regional regulations, the maximum transmission power allowed on the UNII bands is restricted in the firmware, as indicated below: |
| |
 |
| Receiver Sensitivity |
802.11b:
-93 dBm @ 1 Mbps, -93 dBm @ 2 Mbps
-93 dBm @ 5.5 Mbps, -88 dBm @ 11 Mbps
802.11g:
-88 dBm @ 6 Mbps, -86 dBm @ 9 Mbps
-85 dBm @ 12 Mbps, -85 dBm @ 18 Mbps
-85 dBm @ 24 Mbps, -82 dBm @ 36 Mbps
-78 dBm @ 48 Mbps, -74 dBm @ 54 Mbps
802.11n (2.4 GHz):
-70 dBm @ MCS7 20 MHz, -69 dBm @ MCS15 20 MHz
-67 dBm @ MCS7 40 MHz, -67 dBm @ MCS15 40 MHz
802.11a:
-90 dBm @ 6 Mbps, -88 dBm @ 9 Mbps
-88 dBm @ 12 Mbps, -85 dBm @ 18 Mbps
-81 dBm @ 24 Mbps, -78 dBm @ 36 Mbps
-74 dBm @ 48 Mbps, -72 dBm @ 54 Mbps
802.11n (5 GHz):
-69 dBm @ MCS7 20 MHz, -71 dBm @ MCS15 20 MHz
-63 dBm @ MCS7 40 MHz, -68 dBm @ MCS15 40 MHz |
| • Protocol Support |
| General Protocols |
Proxy ARP, DNS, HTTP, HTTPS, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, DHCP, VLAN, STP/RSTP |
| • Interface |
| Default Antennas |
2 dual-band omni-directional antennas, 2 dBi, RP-SMA (male) |
| Connector for External Antennas |
RP-SMA (female), 500 V insulation |
| LAN Ports |
1, RJ45, 10/100/1000BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDI-X connection |
| Console Port |
RS-232 (RJ45-type) |
| Reset |
Present |
| LED Indicators |
PWR1, PWR2, PoE, FAULT, STATE, SIGNAL*, WLAN, LAN |
| • *signal strength indicator |
| Alarm Contact (digital output) |
1 relay output with current carrying capacity of 1 A @ 24 VDC |
| Digital Inputs |
2 electrically isolated inputs• +13 to +30 V for state “1”
• +3 to -30 V for state “0”
• Max. input current: 8 mA |
| • Management |
| Device Management |
Wireless Search Utility, MXconfig, SNMP |
| Network Monitoring |
MXview |
| • Physical Characteristics |
| Housing |
Metal, IP30 protection |
| Weight |
860 g (1.9 lb) |
| Dimensions |
52.7 x 135 x 105 mm (2.08 x 5.32 x 4.13 in) |
| Installation |
DIN-rail mounting (standard), wall mounting (optional) |
| • Environmental Limits |
| Operating Temperature |
Standard Models: -25 to 60°C (-13 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F) |
| Storage Temperature |
-40 to 85°C (-40 to 185°F) |
| Ambient Relative Humidity |
5% to 95% (non-condensing) |
| • Power Requirements |
| Input Voltage |
12 to 48 VDC, redundant dual DC power inputs or 48 VDC Power-over-Ethernet Plus (IEEE 802.3af compliant) |
| Input Current |
0.6 A @ 12 VDC;0.15 A @ 48 VDC |
| Connector |
10-pin removable terminal block, 500 V insulation |
| Power Consumption |
7.2 W |
| Reverse Polarity Protection |
Present |
| • Standards and Certifications |
| Safety |
UL 60950-1, EN 60950-1 |
| Hazardous Location |
UL/cUL Class I Division 2, ATEX Zone 2 |
| EMC |
EN 61000-6-2/6-4 |
| EMI |
CISPR 22, FCC Part 15B Class B |
| EMS |
IEC 61000-4-2 ESD: Contact: 8 kV; Air: 15 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 3 V/m
IEC 61000-4-8 PFMF: 1 A/m |
| Radio |
EN 301 489-1/17, EN 300 328, EN 301 893, TELEC, FCC ID SLE-WAPN008, KC, RCM, MIC, ANATEL, WPC |
| Note |
Please check Moxa’s website for the most up-to-date certification status. |
| • MTBF (mean time between failures) |
| Time |
770,854 hrs |
| Standard |
Telcordia SR332 |
|
|
|
|
|
|
