1.800.301.9097
COVID-19 Response: a note to our customers. 
We're here to help.Learn More>

Login / Register Contact Us
 
EZBR-0214HD+ - EZ-Bridge LT2 HD+ Industrial Strength PtP Bridge System- Plug and Play 2.4GHz, 802.11bg/n, 250mW. Surge Protected by Tycon Systems

EZBR-0214HD+ - EZ-Bridge LT2 HD+ Industrial Strength PtP Bridge System- Plug and Play 2.4GHz, 802.11bg/n, 250mW. Surge Protected
by Tycon Systems

Write a review Write a review
  • High Power Electronics and powerful advanced MIMO antenna
  • True Plug and Play
  • 64 and 128bit WEP, WPA and WPA2 Encryption
  • Web-based configuration
  • Power over Ethernet
  • Layer 2 Transparent Bridge
  • Mfg SKU # : EZBR-0214HD+
    List Price : $399.95
    Our Price : $392.00
    Stock :24
    Quantity :

    EZBR-0214HD+ is the EZ-BridgeLT2+HD is a Industrial Strength high power outdoor 250mW wireless bridge system operating in the 2.4GHz unlicensed frequency spectrum providing real world thruput up to 100 Mb/sec.

    It complies with the 802.11bgn standards to insure interoperability.

    The EZ-BridgeLT2+HD comes with two 75' shielded, outdoor rated(CMX) CAT5 cable assemblies and POE Inserters with built in surge protection on the Ethernet data and power lines.

    The EZ-Bridge creates a transparent wireless bridge between two networks up to 3 miles apart with good line of sight.

    It supports multiple MAC addresses and DHCP across the wireless link.

    It is the perfect plug and play solution for connecting the networks in two or more buildings, internet access sharing, remote video surveillance or remote network access.

    Multiple EZ-Bridge units can be connected in a mesh configuration to allow interconnecting more than two sites. Using the EZ-GO2+ Wireless Network Expansion Units, you can create a network between an odd number of buildings like 3 or 5 sites.

    With its password verification, MAC address authentication, SSID suppression and advanced WPA2 encryption, the system provides the best available wireless data security.

    Installation is a snap because of the plug and play features which have been built into the system. Just install the antennas and plug in the power supplies. The units will automatically find their peer and create a secure wireless network link. If changes to the pre-configured settings are desired, they can be easily done thru the built-in web interface from any point on either side of the network. There are no drivers or software that needs to be loaded to the computer.

    The EZ-BridgeLT2+HD comes complete with all the electronics that are needed for a point to point wireless network bridge installation; including 2 powerful 14dBi MIMO antennas with built-in 802.11bgn high power electronics, Bracket Kits which accommodate pole or wall mounting, Two 75' shielded and outdoor rated CAT5 cable assemblies and two Autoranging PoE Inserters with built in surge protection on the Ethernet data and power lines. Customer needs to supply CAT5 cabling between the PoE Inserter and the router, switch or computer.

    Data Rates 2.4Ghz 802.11n: up to 300Mbps 2.4 GHz 802.11g: up to 54Mbps 5GHz 802.11n: up to 300Mbps 5GHz 802.11a: up to 54Mbps
    Standards IEEE802.11g/n, 802.11a/n, 802.3, 802.3u
    Power Requirements Power Supply: 100-240VAC 50/60Hz EZ-Bridge: 12VDC to 24VDC Passive PoE Average Power Consumption: 4W
    Regulatory Certifications FCC Part 15 / UL
    RF Frequency Band 2400 ~ 2497 MHz 5100 ~ 5850 MHz
    Modulation Technology 802.11n: TDMA 802.11g: OFDM 802.11a: OFDM
    Receive Sensitivity (Typical) 802.11n: -90 dBm 802.11g: -75 dBm 802.11a: -75 dBm
    Transmit Power 25dBm 316mW
    DC Connector Power Out Input Voltage @ Max 10W
    Antenna 2.4GHz 14dBi MIMO Panel Antenna, 35deg Beamwidth, >20dB front to back 5GHz 16dBi MIMO Panel Antenna, 27deg Beamwidth, >22dB front to back
    Operation Mode – Bridge or Router Point to Point Bridge, Access Point, Access Point WDS, Client, Client WDS
    Interface 10/100Mbps RJ-45 LAN Port x 2
    IP Configuration Static or Auto configuration using DHCP Client
    Security MAC Address Filtering, WEP/WPA encryption, Hide SSID in beacons, Layer 2 isolation
    Management Configuration Web-based configuration (HTTP) Console configuration (SSH) SNMP Protocol
    Firmware Upgrade Upgrade firmware via web browser
    Antenna Physical Dimensions (L x W x D) 314mm x 187mm x 65mm 12.4” x 7.3” x 2.5”
    Complete System Weight 3 kg (7 lbs )
    Operating Temperature -30°C to +70°C (-22°F to 158°F)
    Warranty 1 Year

    Copyright © 2022 iComTech. All rights reserved. Shopping Cart Software powered by ecMidas.