ICP DAS NSM-209FC - NS-209FC with Metal Case
by ICP DAS

Unmanaged 8-Port Industrial 10/100 Base-T with 100 Base-FX Fiber Switch with SC Connector, Multi-mode

Description
Specification
Datasheet

The NSM-209FC (SC Connector; Multi-mode) is a Unmanaged 8-Port Industrial Ethernet(10/100Base-TX) with Fiber(100Base-FX) Switch that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is used Ethernet for transmitting a signal up to 2 Km(6,600 ft), and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.

The NSM-209FC operates at either half or full duplex mode. In full duplex mode, range is 2km with 62.5/ 125μm fiber cables; in half duplex mode, range is 412m with 62.5/ 125μm fiber cables.

The Ethernet supports 10/ 100M auto-negotiation feature and auto MDI /MDIX function.

NSM-209FC provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the NSM-209FC's power needs.

Features

Automatic MDI / MDI-X crossover for plug-and-play
Each port supports both 10/100 Mbps speed auto negotiation
Store-and-forward architecture
Full duplex IEEE 802.3x and half duplex backpressure flow control
3.2 Gbps high performance memory bandwidth
Redundant Power Inputs +10 ~ +30V DC
Power failure alarm by relay output
Supports operating temperatures from 0 ~ +70°C
IP20, rugged high-strength metal case
DIN rail mount for industrial usage

Technology
Standards	IEEE802.3, 802.3u, 802.3x
Processing Type	Store & forward wire speed switching - no delays
MAC Addresses	1024
Memory Bandwidth	3.2 Gbps
Flow Control	IEEE802.3x flow control, back pressure flow control
Interface
RJ45 port	10/100BaseT(X) auto negotiation speed, F/H duplex mode, and auto MDI/MDIX connection
Fiber Optic port	100 Base-FX(Multi-mode; SC connector)
LED Indicators	10/100M, Link/Act, Full duplex/Half duplex(Fiber Port)
Ethernet Isolation	1500 Vrms 1 minute
Frame Ground for EMS Protection	Yes
Fiber Optic	Multi mode fiber cables:50/125, 62.5/125 or 100/140 μm
	Distance :2 km, (62.5/125 μm recommended) for full duplex
	Wavelength : 1300 or 1310nm
	Min. TX Output:- 20 dBm
	Max. TX Output: -14 dBm
	RX Sensitivity: -34 to -31 dBm
Ethernet Transmission distance	Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm
Ethernet Transmission distance	Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm
Power
Redundant Input Range	+10 ~ +30VDC (Non-isolation)
Alarm Contact	One relay output with current carrying capacity of 2A @ 30 VDC
Power consumption	0.17A@24VDC, +/- 5% arrowed with 100M Full duplex
LED Indicators	Power input1, Power input2, Power fail
Protection	Power reverse polarity protection
Frame Ground for EMS Protection	Yes
Connection	7-Pin Removable Terminal Block
Mechanical
Case	Metal
Environmental rating	IP20
Dimensions	72.5mm x 110mm x 102mm (W x H x D)
Installation	DIN rail mount; Wall Mounting
Environmental
Operating Temperature	0 ~ +70°C
Storage Temperature	-20 ~ +85°C
Ambient Relative Humidity	10% to 90% non-condensing