|
|
|
- Supports 1 port 10/100Base-T(X) auto-negotiation and auto-MDI/MDI-X
- Supports Ethernet to fiber with SFP socket
- Support LFP (Link Fault Pass-through) function
- Supports full/half duplex operation mode
- P.S.E. fully compliant with IEEE802.3at standard, provide up to 30 Watts
- Supports store and forward transmission
- Provided DIP-Switch to set operation mode
- High reliability and rigid IP-30 housing
- DIN-Rail and panel mounting enabled
|
|
|
IPMC-111PB is a cost-effective solution for the conversion interface between
10/100Base-T(X) and 100Base-FX, it allows you to extend communication distance
by optical fiber. IPMC-111PB supports MDI/MDIX auto detection, so you don’t need
to use crossover wires. IPMC-111PB also support Power over Ethernet, a system to
transmit electrical power up to 30 watts, along with data, to remote devices
over standard twisted-pair cable in an Ethernet network. Each IPMC-111PB has
1x10/100Base-T(X) P.S.E. (Power Sourcing Equipment) port to provide power in a
PoE setup. IPMC-111PB with wide operating temperature range from -40°C~70°C and
accepts a wide voltage range from dual 50~57 VDC power inputs, so it is suitable
for harsh operating environments.
IPMC-111PB also supports the LFP (Link Fault Pass-through) feature. When one
side of the link fails, the other side continues transmitting packets, and
waiting for a response that never arrives from the disconnected side. Use the
DIP-Switch to enable the LFP function, then IPMC-111PB will force the link to
shutdown as soon as noticed that the other link has failed, to notice the
administrator to react to the situation. Therefore, the IPMC-111PB is reliable
media converter with PoE capability and can satisfy most demand of operating
environment
| Physical Ports |
|
| 10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX |
1 |
| Technology |
|
| Ethernet Standards |
IEEE 802.3 for 10Base-T
IEEE 802.3u for 100Base-TX and 100Base-FX
IEEE 802.3x for Flow control
IEEE 802.3at PoE specification (up to 30 Watts per port for P.S.E.) |
| Processing |
Store-and-Forward |
| DIP-Switch setting |
DIP-Switch 1 for LFP mode selection : (ON) enable / (OFF) disable
DIP-Switch 2 for Ethernet speed selection : (ON)10Mbps / (OFF)
10/100Mbps Auto-negotiate
DIP-Switch 3 for Ethernet full/half duplex selection : (ON) Half-duplex
/ (OFF) Full/Half-Duplex Auto-negotiate
DIP-Switch 4 for fiber full/half duplex selection : (ON) Half-Duplex /
(OFF) Full-Duplex |
| LED Indicators |
|
| Power indicator |
Green : Power LED x 2 (ON : power input on-line / (OFF) power input
off-line |
| 10/100Base-T(X) RJ45 port indicator |
Green for port Link/Act – (ON) Link up / (Blinking) Acting / (OFF)
Link down
Amber for 100Mbps/10Mbps indicator – (ON) Working at 100Mbps / (OFF)
Working at 10Mbps
Green for port duplex indicator – (ON) Full-Duplex / (OFF) Half-Duplex |
| 100Base-FX fiber port indicator |
Green for fiber port Link/Act - (ON) Link up / (Flash) Acting /
(OFF) Link down
Green for fiber port duplex indicator – (ON) Full-Duplex / (OFF)
Half-Duplex |
| LFP statue indicator |
Amber LED – (ON) LFP function fail / (OFF) LFP function disable |
| PoE indicator |
Amber for P.S.E. indicator |
| Power |
|
| Input power |
Dual 50~57 VDC voltage power inputs at 4-pin terminal block |
| Power consumption (Typ.) |
31.2 Watts (P.S.E. output included) |
| Overload current protection |
Present |
| Reverse polarity protection |
Present |
| Physical Characteristic |
|
| Enclosure |
IP-30 |
| Dimension (W x D x H) |
26.1 (W) x 70 (D) x 95 (H)mm (1.03 x 2.76 x 3.74 inch) |
| Weight (g) |
210 g |
| Environmental |
|
| Storage Temperature |
-40 to 85°C(-40 to 185°F) |
| Operating Temperature |
-40 to 70°C (-40 to 158°F) |
| Operating Humidity |
5% to 95% Non-condensing |
| Regulatory approvals |
|
| EMI |
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2, EN55011,
EN50121-4) |
| EMS |
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5
(Surge), EN61000-4-6 (CS), EN61000-4-8,
EN61000-4-11 |
| Shock |
IEC60068-2-27 |
| Free Fall |
IEC60068-2-32 |
| Vibration |
IEC60068-2-6 |
| Safety |
EN60950-1 |
| Warranty |
5 years |
|
|
|
|
