|
|
|
ICP DAS MSM-508FCS-T - 8 Port 10 /100 Base T Managed Switch with Metal case, FC connector, Single Mode
by ICP DAS
|
|
|
|
8-port Layer 2 Managed Switch with 2-Fiber Port, Single-mode, SC Connector (RoHS)
|
|
|
The MSM-508F series is an 8-port Industrial Ethernet Layer 2 Managed Switch with 2-Fiber Port that secures data transmission by using fiber optic transmission to provide immunity from EMI/RFI interference. It is perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion. It can be managed through RS-232 port via serial console or Ethernet port using telnet or Web browser. In addition, the switch supports a lot of powerful managed functions, such as 802.1Q Tag-based VLAN, Portbased VLAN, 802.1p QoS (Quality of Service), Port Trunking, Spanning Tree, Cable Testing and Port Mirroring. Built-in ICP DAS Cyber-Ring technique that enable multiple switches to be placed into a redundant ring. Typically it detects and recovers from a fi ber or copper link failure within approximately 20 ms V for the majority of applications a seamless process. Modbus/TCP, Modbus/RTU and OPC supported, SCADA application can monitor status of Ethernet and fiber port with Modbus or OPC protocol. MSM-508F provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the it's power needs. And the relay output facility can deliver warning signal while power or network link failure.
- Automatic MDI/MDI-X crossover for plug-and-play
- Ech port supports both 10/100 Mbps speed auto negotiation
- Store-and-forward architecture
- Full duplex IEEE 802.3x and half duplex backpressure flow control
- 3.2 Gbps high performance memory bandwidth
- Frame buffer memory: 1 Mbit
- Integrated look-up engine with dedicated 2048 unicast MAC addresses
- Supports +12 VDC ~ +48 VDC Power failure alarm by relay output
- Supports operating temperatures from 0 °C ~ +70 °
- DIN-Rail mount and Screw hole for wall mounting kit
- DIN rail mount and Screw hole for wall mounting kit.
| Technology |
| Standards |
IEEE 802.3, IEEE 802.3u, IEEE802.3x |
| Processing Type |
Store & forward wire speed switching - no delays |
| MAC addresses supported |
2048 |
| Memory Bandwidth |
3.2 Gbps |
| Frame Buffer Memory |
1 Mbit |
| Flow Control |
IEEE802.3x flow control, back pressure flow control |
| Protocol |
VLAN, QoS, Port Trunk, SMTP, TELNET |
| Interface |
| RJ45 port |
10/100BaseT(X) auto negotiation speed, F/H duplex mode,
and auto MDI/MDIX connection |
| Fiber Optics Port |
100 Base-FX |
| LED Indicators |
10/100M, Link/Act/Backup, Full duplex/Half duplex (Fiber Port) |
| Ethernet Isolation |
1500 Vrms 1 minute |
| Frame Ground for EMS Protection |
Yes |
| Multi Mode |
Multi Mode fiber Cables: 50/125, 62.5/125 or 100/140 μm |
| Distance 2km, (62.5/125 μm recommended) for full duplex
|
| Wavelength: 100 or 1310 nm |
| Min. TX Output: -20dBm |
| Max. TX Output: -14 dBm |
| EX Sensitivity: -34 ~ - 31 dBm |
| Single Mode |
Single Mode fiber Cables; 8.3/125, 8.7/125, 9/125 or 10/125 μm |
| Distance 15km, (9/125μm recommended) for full duplex |
| Wavelength: 130100 or 1310 nm |
| Min. TX Output: -15 dBm |
| Max TX Output: -8dBm |
| RX Sensitivity: -36 ~ -31dBm |
| Frame Ground for EMS Protection |
Yes |
| Ethernet Transmission distance |
Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm |
| Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm |
Fiber Optic
Transmission distance |
Single-mode fiber cables:8.3/125, 8.7/125, 9/125 or 10/125 μm |
| Distance :15 km, (9/125 μm recommended) for full duplex |
| Wavelength : 1300 or 1310nm |
| Min. TX Output: -15 dBm |
| Max. TX Output: -8 dBm |
| RX Sensitivity: -36 to -31 dBm |
| Ethernet Cables |
10 Base-T (Cat.3, 4, 5 UTP cable; 100m Max.)
100 Base-TX (Cat.5 UTP cable; 100m Max.) |
| Management interface |
Console, DIP/Rotary Switch |
| COM 1 |
RS-232 (TXD, RXD and GND); Non-isolation |
| COM 2 |
RS-485 (D2+, D2-; self-tuner ASIC inside); Non-isolation |
| Digital Input/Out |
| Digital Input |
3-channel, Wet contact, L: +11 VDC Max, H: +19 VDC ~ +30 VDC |
| Digital Output |
3-channel, Open Collector, Sink/NPN, 30V/100 mA Max. |
| Power |
| Input Voltage Range |
+12 VDC ~ +48 VDC (Non-isolation redundant input) |
| Power Consumption |
0.3 A @ 24 VDC, +/-5% arrowed with 100M Full duplex |
| LED Indicator |
Yes |
| Protection |
Power reverse polarity protection |
| Frame Ground for EMS Protection |
Yes |
| Mechanical |
| Case |
Metal (IP30 Protection) |
| Dimensions (W x L x H) |
47 m x 140 mm x 175 mm |
| Installation |
DIN rail mount; Wall Mounting |
| Environmental |
| Operating temperature |
0°C~ +70°C |
| Storage Temperature |
-20°C ~ +85°C |
| Relative Humidity |
10% to 90% RH, non-condensing |
| Include Cable |
| |
CA-090510 x 1 |
|
|
|
|
