Need assistance or guidance?

Contact us @: 1-800-301-9097
Login / Register Contact Us
 
IGAR-1062(+)-4G - Industrial IEEE 802.11 a/b/g/n 4G Cellular Router with 2x10/100/1000Base-T(X) by ORing Industrial Networking

IGAR-1062(+)-4G - Industrial IEEE 802.11 a/b/g/n 4G Cellular Router with 2x10/100/1000Base-T(X)
by ORing Industrial Networking

Write a review Write a review
  • High Speed Air Connectivity: WLAN interface support up to 300Mbps link speed
  • Provide 2 port 10/100/1000Base-T(X) port and 1 sim card slot
  • 4G LTE Modem dial up included
  • Provide HNAT enhance LAN to WAN routing performance
  • Highly Security Capability: WEP/WPA/WPA-PSK(TKIP,AES)/ WPA2/WPA2-PSK(TKIP,AES)/802.1X Authentication supported
  • Secured Management by HTTPs
  • Various kind of WAN Connection Type supported: Dynamic/Static IP, PPPoE, Modem/Dial Up
  • Support client operating mode
  • IP table to prevent access from unauthorized IP address
  • Support VPN for secured network connection (Open VPN , PPTP, IPSEC VPN)
  • Support NAT Setting (Virtual Server , Port Trigger , DMZ , UPnP)
  • 3G Modem signal information display (un-connecting status)
  • Wireless connecting status monitoring
  • Versatile modes & event alarm by e-mail
  • 1KV isolation for PoE P.D. port 
  • Event Warning by Syslog, Email, SNMP Trap, Relay and Beeper
  • Rigid IP-30 housing design
  • DIN-Rail and Wall-mount enabled
IGAR-1062+-4G is a reliable IEEE 802.11 a/b/g/n WLAN 4G LTE router with 2 ports 10/100/1000Base-T(X) router where ETH1 for LAN and ETH2 for WAN. It supports 802.1X and MAC filter for security control. It could be configured to operate in 3 modes of routing function: Dynamic/Static IP route, PPPoE authentication, and Modem (GPRS/3G/3.5G/LTE Modem) dial up. Users can set up WLAN environment to fulfill demands of various applications rapidly by dialing up cellular modems. In addition, IGAR-1062+-4G provides P.D. feature on ETH2 which is fully compliant with IEEE802.3af PoE P.D. specification. This feature extends the layout up to 100 meters. Therefore, IGAR-1062+-4G is one of the best solution for applications of wireless communication.
Physical Ports    
10/100/1000Base-T(X) Ports in RJ45 Auto MDI/MDIX 2
P.O.E. PD port

Present at ETH2
Fully compliant with IEEE 802.3af   Power
Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance :10^8 ohms min

5-Pin Terminal Block 4(DI and DO)
Sim Card Slot 1
Cellular Interface    
Cellualr Standard GSM / GPRS/ EGPRS/ EDGE / WCDMA / HSDPA / HSUPA / LTE
Band Option America(US)
LTE:
700/1700/2100/ MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
800/850/1900/2100 MHz
GSM/GPRS/EDGE:
850/900/1800/1900 MHz
Europe(EU)
LTE:
800/900/1800/2100/2600 MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
900/2100 MHz
GSM/GPRS/EDGE:
900/1800/1900 MHz
Antenna Connector 1 x SMA Female
WLAN interface    
Operating Mode AP/Bridge/Repeater/AP-Client
Antenna and connector 2 x RP-SMA Female
Radio Frequency Type DSSS
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11a/g: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
IEEE802.11n: OFDM with BPSK, QPSK, 16-QAM, 64-QAM
Frequency Band America / FCC:
2.412~2.462 GHz (11 channels )
5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )
Europe CE / ETSI:
2.412~2.472 GHz ( 13 channels )
5.180~5.240 GHz ( 4 channels )
Transmission Rate IEEE802.11b: 1/ 2/ 5.5/ 11 Mbps
IEEE802.11a/g: 6/ 9/ 12/ 18/ 24/ 36/ 48/ 54 Mbps
IEEE802.11n:up to 300Mbps
Transmit Power 802.11a: 12dBm ± 1.5dBm@54Mbps
802.11b: 17dBm ± 1.5dBm@11Mbps
802.11g: 16dBm ± 1.5dBm@54Mbps
802.11gn HT20: 15dBm ± 1.5dBm @MCS7
802.11gn HT40: 14dBm ± 1.5dBm @MCS7
802.11an HT20: 12dBm ± 1.5dBm @MCS7
802.11an HT40: 11dBm ± 1.5dBm @MCS7
Receiver Sensitivity 802.11a : -76dBm ± 2dBm@54Mbps
802.11b : -85dBm ± 2dBm@11Mbps
802.11g : -76dBm ± 2dBm@54Mbps
802.11gn HT20:-75dBm ± 2dBm@MCS7
802.11gn HT40:-72dBm ± 2dBm@MCS7
802.11an HT20:-74dBm ± 2dBm@MCS7
802.11an HT40:-71dBm ± 2dBm@MCS7
Encryption Security WEP: (64-bit ,128-bit key)
WPA/WPA2 PSK :TKIP and AES encryption (802.11i)
802.1X/RADIUS Authentication supported
Wireless Security SSID broadcast disable
LED Indicators    
Power Indicator 3 x LEDs, PWR1(2)(PoE) / Ready:
Red On : Power is on and booting up
Green On : Power is on and functioning Normal
10/100/1000T RJ45 Port Indicator 2 x LEDs,
LNK/ACT:Green for port Act.
Speed: Green for port Link at 1000Mbps
Amber for port Link at 100Mbps.
Off for port Link at 10Mbps
WLAN LEDs Green Solid On: RF on, Blink: data transmitting
Green for WLAN Strength: 1<25%, 2<50%, 3<75%, 4<100%
WAN LEDs Green On : Power is on and functioning Normal
Fault 1 x LED, Red for Ethernet link down or power down indicator
Fault contact    
Relay Relay output to carry capacity of 1A at 24VDC
Power    
Redundant Input Power Dual DC inputs. 12-48VDC on 6-pin terminal block
Power Consumption (Typ.) 9.5W
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic    
Enclosure IP-30
Dimension (W x D x H) 74.3(W) x 109.2(D) x 153.6(H) mm (2.93 x 4.3 x 6.05 inch.)
Weight (g) 1155
Environmental  
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -25 to 70°C (-13 to 158°F)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals    
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-32
Vibration IEC60068-2-6
Safety EN60950-1

Copyright © 2024 iComTech. All rights reserved. Shopping Cart Software powered by ecMidas.